SM0837- PAPER MACHINE 4,000MM, 130 TPD, graphic papers
1. General information
- Location: Europe
- Status of the PM: Stopped in 2011, completely assembled, in very good mechanical conditions (repair of some parts required)
- Status of the mill: In liquidation procedure
- Parts for sale: Paper machinery, approach flow system, auxiliary systems, winder, available spare parts, wrapping machine, de-inking line (offered separately). Dismantling service.
2. PM general
- Original manufacturer: Voith
- Year of construction: 1932 (the PM has been rebuilt several times until 2003, there are no original parts)
- Other manufacturers: Escher-Wyss, Metso, Omma, Sonotec
- Hand of machinery: Right (drive on the right side when looking at reel from headbox)
- Designed for: Uncoated graphic paper grades
- Raw material: DIP (de-inked pulp from mixed office waste)
- Basis weight range: 45 – 150 gsm
- Wire width: 4,000 mm
- Paper width at reel : 3,750 mm
- Maximum operating speed: 600 mpm
- Daily production (average): 130 Tons
3. PM main characteristics
Headbox
- • Metso, installed in 1995 • Air-cushion type
- • Slice width of 4050 mm • Designed for 150 BDTPD
Wire section
- •Manufactured by OMMA in 1992 and rebuilt in 2001 by Metso
- • Fourdrinier type, in cantilever
- • Structure in stainless steel and carbon steel lined with s.s. plates • Length of 12850 mm, wire width of 4200 mm
- • Suction couch roll of 762 mm diameter
Press section
- • 1st press rebuilt by Metso in 2001, pick-up press with felted suction roll 812 mm diameter and granite center roll 875 mm diameter
- • 2nd press installed in 1992 by Escher-Wyss, felted bottom overall deflection roll (Nipco) 545 mm diameter, top center roll 955 mm diameter
Dryer section
- • Rebuilt in 1995 by Metso
- • Pre-dryer section composed by (17) cast iron dryers 1500 X 3950 mm @ 4.9 bar steam pressure
- • Post-dryer section composed by (10) cast iron dryers 1500 X 3950 mm @ 4.9 bar steam pressure
- • Configuration of the pre-dryer section: Uno-run (single-felt) for the first battery, conventional two-tier felt design for the second and third batteries • Configuration of the post-drying section: conventional two-tier felt design • Completed of rope threading system (rope groove on dryers)
- • Composed by a silent drive system (drive on dryers)
- • Centralized oil lubrication system (Safematic)
- • Steam and condensate system designed by Langbein Engelbracht
Size press
- • Manufacturer: Sonotec
- • Puddle type, inclined design
- • 590 mm top (hard) roll diameter / 600 mm bottom (soft) roll diameter • Completed of starch preparation system and working stations
Calender
- • Installed in 1992 by Escher-Wyss
- • Hard nip type
- • Top roll 660 mm diameter, Equitherm
- • Bottom roll 500 mm diameter, overall deflection roll (Nipco) • Completed of hydraulic station
- • Completed of thermal station
Reel
- •Installed in 1995 by Metso
- • Drum reel type, hydraulic
- • Drum diameter of 1100 mm
- • Parent roll diameter of 2600 mm (max.)
- • Completed of automatic spool loading storage • Provided with (5) spools 400 mm diameter
UTM pulpers
- • (1) couch pit in concrete lined with stainless steel plates composed by an horizontal shaft agitator completed of reducer and AC electric motor
- • (1) dry broke pulper composed by a stainless steel vat, central group (propeller, bearings support, shaft, couplings, safety protections), reducer and AC electric motor
Drying hood
- • Pre-dryer closed hood 18.5 X 7 X 4.65 m
- • Post-dryer closed hood 8,5 X 7 X 4,65 m
- • Completed of exhausted air conditioning system
Quality control system
- • ABB QCS
Control system
- • Completed of MCS, MCC
Drive
- • AC
4. Winder specification
Jagenberg Vari Step TR 43
- • Two-drum type
- • Maximum speed of 2000 mpm
- • Unwound roll of 2400 mm diameter (max.)
- • Wound roll of 1525 mm diameter (max.)
- • (10) knives
- • PLC control system
- • (3) DC electric motors (135 kW + 120 kW + 120 kW)
- • Complete with roll inertia compensation system (regenerative brake) • Provided with suction trimming chips system
5. Exclusions
- • The following parts are excluded from the supply: building, cranes, cogeneration plant.
6. De-inking line 150tpd
At the time of writing, the de-inking line is composed of the equipment listed below.
- • Pulper HD20 RCM including belt conveyor with weighing system and de-trashing system (pulper screen RCM TSP 1300 type)
- • Pulper Escher-Wyss ST6C 9 mc with slat conveyor and electronic weighing system
- • Stock chests (3 in total), built in 1992 by Sonotec, are in stainless steel with reinforcing ribs in carbon steel. They have about 100 cu.mt capacity and are equipped with agitators Economix by De Pretto – Escher-Wyss type
- • HDC
- • Omnisorter OS2-LR
- • Rejectsorter (De Pretto - Escher-Wyss type RS – 2B) • Omniscreen OS4-BR and Axiguard CS3t
- • Flotation cell by COMER S.p.A.
- • Cleaning system including:
- 1st stage by PalMac with 28 cones
- 2nd stage by PalMac with 10 cones
- 3rd stage by Celleco with 8 cones
- 4th stage by Sulzer-Escher-Wyss with 2 cones
- • Two disks thickeners by Comer
- • Wire press is by Andritz, type CPF 2000
- • Maule thickening system composed by one inclined screw thickeners with two units (type MB75/2) and a dewatering screw press GR-II type
- • Disperging system including one heated screw having 1100 mm diameter and length 9000 mm, high consistency disperger De Pretto – Escher-Wyss type HD3 with electric motor of 550 kW - 660V
Front view drawing of the paper machinery available upon request.